Craps Throwing Station

How To Build Your Own Practice Table

. Make your practice set truly feel like a casino craps table by adding our throwing station. With both pieces your have 98% of what a full table is without the needed room to put one in your home or office. And the cost for both pieces is about half the cost of our full table or any full craps table on the internet. Playtika uses cookies to store information on Craps Throwing Station your computer. Some are essential to make this site work; others help us improve your experience. You consent to the placement of these cookies.

New & Improved
Upgraded Practice Table With Shooting Station

Looking for Dice Layouts, Chip Rail and Corners for your table find them here.
Before you start your pactice table, maybe refresh your knowlege of the game with Free Craps Lessons?

Practice Table Construction (updated 05/30/02)

Materials: (total cost about $200)

Tools:

General Info

The sides and bottom base of the practice table are made from one sheet of 4'x8' 1/2' plywood. It can be any type of any plywood, but birch or oak will make a better looking table and will dice will not dent as easily. The top rail of 1/2' plywood adds strength and helps maintain shape and it can be upholstered if desired. It is important to make the table solid. Making the bottom base a single layer reduces cost but compromises authenticity.

By purchasing the plywood at a Home Depot or Lowe’s they will make some of the cuts for you. Two cuts are free. Have the sheet split lengthwise with one side 24' wide. Split the 24' wide strip in two pieces giving 2 - 24'x47 15/16' pieces (you lose 1/8' for saw blade). Depending on size requirements the bottom base could be trimmed to 47 1/2' as shown in the drawing or left at 47 15/16' width. The other piece would be ripped lengthwise twice to make a 9 1/2' x 96' piece and an 11' x 96' piece.

Bottom Base

Attach the two 24'x47� ' pieces together using six to eight 1�' #10 flathead wood screws from the bottom side only. Be sure that the screw heads are flush. Layout the 14�' radius corners and cut with a hand held jig (saber) saw. A router can be used to smooth the edges with a 3/8' round over bit top and bottom. The routing is not essential but it makes the felting easier. Do not cover base with felt until the sides are constructed. When covering with felt an under layer of flannel (purchased from a fabric store) reduces the hardness and makes the surface more like casino conditions.

The banquet table legs are 28' in length. Cut 3' to 3�” off the bottom using a tubing cutter of hack saw. Mount the legs, with the screws provided, to the base about 6' in from the edge. Make sure that the smooth surface (no screw heads) of the base is up.

Side Boards

Cutting of the kerfs, which allow the side board to bend around the corner, is accomplished by setting the saw to a depth of 1/16' less than the thickness of the plywood. Try a couple of test cuts on some scrap or the ends to make sure the cut does not go completely through the plywood . If the depth becomes equal or greater than the thickness of the plywood it will ruin the project. Layout the kerf lines 1' apart (�' or 3/4' makes a smoother turn but is a lot more work). Use a straight edge guide to cut the kerfs with a hand circular saw or a radial arm saw. The radial arm saw, if you have one, makes the job much easier. Make sure that there is a rigid board under the entire length of the side board when cutting as the side board will break at the kerfs if there is no support. The ends should not be cut to length until the board is wrapped on the bottom base and marked and cut.

There are two side boards. The outside side plywood is wrapped around the bottom base with the kerfs facing inward towards the bottom base and with the edge of the outside side flush with the underside of the base. Placing waxed paper around the edge and on top of the base will keep glue in its place. Wetting the smooth surface of the plywood with a spray bottle, where the kerfs have been cut, helps bending. Clamps or temporary nails hold the outside side plywood in place against the base. Do not drive nails all the way in as they will be removed when the inside side board is glued into position.

Apply wood glue to inside surface (kerf side)of the outer side. Carefully bend the inside plywood side (kerf of inside plywood facing the kerf of the outside plywood) into position. Clamp or screw using 1�” #10 screws, the inside plywood to the outside plywood (from the inside). Allow adequate time to dry.

The excess sides may now be trimmed with a saw even with the bottom base.

An optional 2' high plexiglass fence added to the front of the table will keep the dice confined to the practice table. I have found it keeps the dice from bouncing off the table when your friends toss the dice. A precision shooter would never make a shot with that much rebound. The plexiglass starts just above the base. Drill holes in plexiglass and attach with 2 1' #6 round head screws.

Top Rail

Cut out the top rail from the �' plywood using a jigsaw. Align on top of the sides and attach using 1�” #10 screws. You can upholster the top rail with 1' foam and vinyl if desired.

Chip rails can be purchased at http://www.casino4you.com/

Felt

Place the flannel on the base (make sure screw heads are on the underside) and staple. Apply the felt over the flannel and attach using a stapler. Start with the straight edge and stretch and staple.

Diamond Rubber

Attach the rubber centered between the curved portions. Use a rubber adhesive as it is a silicone flexible adhesive that will not become brittle.

Craps How To Roll Dice

Shooting Station for Practice Table Construction

Tools:

The sides and bottom base of the shooting stand table are made from one sheet of 4'x8' 3/4' plywood. The top rail of �' plywood is for the rail padding we lean against so much. Optional chip trays are shown but not described. Email me for details on the chip tray if you want to go to this detail.

By purchasing the plywood at a Home Depot or Lowe’s they will make some of the cuts for you. Two cuts are free. The cutting diagram will help.

Station Bottom Base

Attach the two 24'x36' pieces together using 1�' #10 flathead wood screws from the bottom side only. Be sure that the screw heads are flush to avoid marring any surface you set the table up on. A router can be used to do a 3/8' round over on the top and bottom. Cut 3' to 3�” from each leg of the banquet table legs using a tubing cutter (a hacksaw will work but is a lot more work and the result is not as smooth).

Next attach the banquet table legs. Place them about 6' from the ends of the base and attach with screws provided with the legs.

The base must be covered with felt prior to installing the side. Stretch and staple to the station base.

Side Boards

Sandwich the �' x 36' (9� “ and 11' high) side boards and use 1�' #10 flathead wood screws from the 9�' side to secure the two pieces. Be sure that the screw heads are flush.

Place the sandwiched plywood side board on the felted base and attach with 3 2' #10 wood screws.

Attach the �” plywood, 6�' wide top cap to the side boards using 1�' #10 wood screws. You may add chip rails if you desire. Chip rails are made out of 1' thick mahogany. It takes some woodworking skill to make the chip rails.

The �” x �' x 38' piece must be glued to the �' x 3�' x 38' plywood before the corners are rounded. After this step apply 1' foam over the top and front of the plywood. Staple the vinyl upholstery fabric to the rail for a casino like rail rest.

Happy Shooting

DiceSetter.com

Kerf detail

Quick and Dirty Practice Table

Supplies:

14’ x 5’ Sheet of 1/2 inch plywood or particle board

12’ x 3’ Sheet of masonite

172” x 48” sheet of felt

Craps Throwing Stations

1Twin size foam mattress pad (twin size)

Craps Throwing Station

1Can of spray paint

1Can of spray adhesive

Tools:Circular saw
Drill
Hammer
Staple Gun

Time:
Approximately 2 hours.If you spray paint the mattress pad, perhaps do this step the evening before.

Cost:
If you don’t have to buy power tools, this will cost around $29.

Construction:

• Cut foam mattress pad into a 12” x 6 ‘ length.Spray paint to desired color (optional)
• Cut plywood to be 4 feet wide by 3 feet deep for base.
• With left over plywood, cut another piece of plywood 4’ long by 12.5” high for the back wall.
• Cut 2 masonite sheets 15” long by 12.5” high for side walls

• Drape felt over plywood.Cut to size such that there is about 2” extra around the perimeter of the plywood.Staple felt to the edges of plywood, keeping it taught.
• Screw back wall to the base
• Screw side wall masonite pieces to the base.Make sure that they overlap to the back wall plywood. Screw masonite side pieces to back wall as well.
• Place mattress pad on the table, inside the 3 walls.You will be able to make curved corners.Once you have the fit that you like, spray adhesive on the inside of the back and side wall pieces AND on the back of the mattress pad.Secure into place.Let dry.

<img src='../images/home1.jpg' alt='home1.jpg (123936 bytes)' width='310' height='234' '='>

Options: You can purchase REAL craps table felt with all the markings and REAL back wall pyramid rubber from http://www.gamblersgeneralstore.com .It will significantly increase the cost of building the table.

Here's the practice table Ray built. A beautiful piece of work!

(under construction)

(finished practice table)

Here is a picture of the practice table Big Lou constructed!

Say hello to the future of craps once these hit Vegas casino floors (via @MeltzVegas) pic.twitter.com/wS1fREeg6T

— Busted Coverage (@bustedcoverage) October 10, 2018

There’s a big gaming convention going on this week in Vegas and one thing that stood out immediately to me as I was going through tweets from media on the ground was this digital craps table where players will have an individual console to place bets and throw dice on a glass top. Definitely odd and definitely coming to Vegas casinos very soon.
Why? The claim is that millennials are more likely to play a digital version of craps and we all know that millennials will own all their parents wealth in the very near future. Vegas is looking to the future and how to separate a 30 year old, who grew up on video games, from his money. I’d also venture to guess that casinos would very much like to eliminate jobs, which would lead to higher profits. Makes sense, right? Of course they’re going to say that’s not the reason for digital games.
From VegasInc.com:

A Las Vegas gaming company hopes a new version of craps that combines a digital layout with a dealer and real dice will make the traditional casino game less intimidating and appeal to millennials and others who might pass by a felt-covered table.
Aruze Gaming’s Roll to Win Craps has been a popular attraction during the Global Gaming Expo this week at the Sands Expo Center.
Players place their bets digitally and roll the dice on a vibrant LED tabletop, with a live dealer monitoring all the action. Payouts are the same as on a regular table.
…
Whitney said he doesn’t see digital table games taking over casino floors, rather offering an alternative for guests who might shy away from the tables altogether.
“I think we have a very good opportunity to grow our (table games) business,” Whitney said. “The one game that keeps growing year over year is craps. It’s a communal game where people can root for one another. When you walk through a casino and you hear the loudest screams, they’re at the craps table.”
“I think the millennial type of customer will gravitate toward that excitement,” he said.

I was pretty surprised by the 50-50 or so reaction to the original tweet. I thought the majority of you would hate the idea of digital craps, but there are those who want speed of play to improve and this will definitely make that happen. There will be no chips and you won’t have 20 different hard way bets being yelled out at once. Enter your bets and go.

Best Way To Throw Dice In Craps

Will that kill the community vibe to craps? I guess if you roll a point, you roll a point. People will always go nuts for that. I think the money on the table aspect fascinates people and that will be lost. The people behind the digital craps table claim it will increase the community effect. Uh, how exactly?

Here’s what the future of kiosk sports betting looks like:

How will it all work?
From TheLines.com:

IGT debuted the CrystalBetting Terminal at G2E. This betting station looks similar to CG Technology betting stations but is made especially for in-play sports betting while watching a game.
Each station allows bettors to customize their screen to show specific games they prefer to watch. The screen also shows in-play odds, and wagers can be placed directly on the screen. Bettors can even play the audio from the game they’re watching instead so they’re not stuck with whatever the sportsbook deems the important game.

You can also pretty much say goodbye to the old ladies taking bets at the sportsbook. Those days will be long gone over the next 10 years and way sooner on the Strip where casinos have to report to stock owners.

Y’all love sports betting kiosks pic.twitter.com/JA0xtfW5SO

— Marc (@MeltzVegas) October 9, 2018

Sports betting kiosks are finally in casinos! I wrote about them and a dope new In Play betting terminal from IGT @TheLinesUShttps://t.co/hl9I3IU6Zgpic.twitter.com/VmUgCnlHKC

— Marc (@MeltzVegas) October 11, 2018